Routing Protocols
ZenPacks.zenoss.RoutingProtocols
This ZenPack provides modeling and monitoring support for devices that are using the following routing protocols:
Border Gateway Protocol (BGP) - Exterior gateway protocol for routing between autonomous systems
Enhanced Interior Gateway Routing Protocol (EIGRP) - Cisco proprietary interior routing protocol
Open Shortest Path First (OSPF) - Interior gateway protocol using link-state routing algorithm
Intermediate System to Intermediate System (ISIS) - Interior routing protocol using link-state routing
Virtual Router Redundancy Protocol (VRRP) - Protocol for automatic default gateway selection
Label Distribution Protocol (LDP) - Protocol for establishing label switched paths
The features added by this ZenPack can be summarized as follows. They are each detailed further below.
Gathers statistics and events from various routing protocols
Support for multiple routing protocol neighbors discovery via SNMP
Monitoring of neighbor states and transitions
IPv4 and IPv6 support for BGP peers
Cisco BGP4 MIB support for enhanced BGP monitoring
Component-based modeling for scalable device monitoring
This ZenPack is compatible with Virtana Service Dynamics 6.9.0 and higher.
Support
This ZenPack is developed and supported by Virtana. Enterprise support is available to Virtana customers with an active subscription or support agreement. ZenPacks are available at delivery.zenoss.com. To request more information about this or any other ZenPack, contact Virtana.
Releases
Version-1.7.1
Released on 2026/03/31
Requires ZenPackLib ZenPack >= 2.0, Cisco Monitor ZenPack.
Compatible with Virtana Service Observability (formerly Zenoss Cloud) and Virtana Service Dynamics 6.9.0
Prerequisites
Required ZenPacks: ZenPacks.zenoss.ZenPackLib >= 2.0, ZenPacks.zenoss.CiscoMonitor.
Discovery
The ZenPack automatically discovers routing protocol neighbors through SNMP polling. The following neighbor types are discovered and monitored:
BGP Neighbors
Component Type: BGPNeighbor
Discovery Method: zenoss.snmp.BGPNeighborMap
Attributes:
BGP Peer Address
BGP Peer State (Idle, Connect, Active, Open sent, Open confirm, Established)
Admin Status (Stop, Start)
Negotiated Version
Local and Remote Port
Remote ASN (Autonomous System Number)
Hold Time and Keep Alive timers
OSPF Neighbors
Component Type: OspfNeighbor
Discovery Method: zenoss.snmp.OSPFNeighborMap
Attributes:
OSPF IP Address
Neighbor State (Down, Attempt, Init, 2-Way, ExStart, Exchange, Loading, Full)
Options (TOS, External Information, Multicast Extensions, NSSA)
Area ID
Interface Type
EIGRP Neighbors
Component Type: EigrpNeighbor
Discovery Method: zenoss.snmp.EIGRPNeighborMap
Attributes:
IP Address and Address Type (IPv4, IPv6, DNS)
Hold Time
Uptime
SRTT (Smooth Round Trip Time)
RTO (Retransmit Timeout)
Queue Count
ISIS Neighbors
Component Type: IsisNeighbor
Discovery Method: zenoss.snmp.ISISNeighborMap
Attributes:
System Type (Level1 IS, Level1 L2 IS)
Circuit Type
Level
State (Up, Down)
VRRP Neighbors
Component Type: VRRPNeighbor
Discovery Method: zenoss.snmp.VRRPNeighborMap
Attributes:
Virtual Router ID (VRID)
Operational State (Initialize, Backup, Master)
Admin State (Up, Down)
Authentication Type
Preempt Mode
Protocol (IP, Bridge, DEC Net, Other)
Traps Enabled Status
LDP Neighbors
Component Type: LDPNeighbor
Discovery Method: zenoss.snmp.LDPNeighborMap
Attributes:
Label Distribution Protocol version
Neighbor identification
State information
Enabling Routing Protocol Monitoring
Select the device or device class
Click on the Modeler Plugins item
Add the appropriate modeler plugin(s) for the protocol(s) you want to monitor, for example
zenoss.snmp.BGPNeighborMap,zenoss.snmp.OSPFNeighborMap,zenoss.snmp.EIGRPNeighborMap, etc.Click Save
Remodel the device
Monitoring and RRD Templates
The ZenPack includes RRD templates for monitoring routing performance metrics:
RoutingPerformance Template: Collects ICMP and IP forwarding statistics
BGP Peer State Monitoring: Tracks BGP peer states and transitions
Protocol-Specific Thresholds: Configurable event thresholds for each protocol
Supported Devices
Devices must be created under the /Devices/Network device class in order to use the RRD templates. The ZenPack supports:
Cisco IOS and IOS-XE based routers
Juniper Junos devices
Other SNMP-enabled routers supporting standard routing protocol MIBs
Attributes and Events
Event Classes
The ZenPack creates events for:
Neighbor state changes
Connection losses
Configuration errors
Protocol-specific anomalies
Component Relationships
All neighbor components maintain relationships to their parent device and can be searched by IP address or other identifying attributes.
Advanced Features
Remote Device Resolution
The ZenPack includes utilities to resolve neighbor IP addresses to remote devices in the Virtana inventory:
Automatic device lookup by IP address
Support for network-based device discovery
Clickable links to remote device pages in the UI
IPv6 Support
BGP neighbors support both IPv4 and IPv6 address families, enabling monitoring of modern dual-stack networks.
Cisco-Specific Enhancements
Enhanced Cisco BGP4 MIB support provides additional metrics and better device compatibility compared to standard MIB support.
Changes
Release 1.7.1
Implemented support for Cisco BGP4 MIB, IPv6 for BGP Peer polling and monitoring (ZPS-9164)
Replaced README.rst with README.md with detailed description
Tested with Virtana Service Observability (formerly Zenoss Cloud) and Virtana Service Dynamics 6.9.0
Release 1.7.0
Add relations to Cisco Device to avoid
relationship not founderror on Cisco deviceTested with Virtana Service Observability (formerly Zenoss Cloud) and Virtana Service Dynamics 6.9.0
Release 1.6.0
Remove references to
RoutingProtocolsDeviceTested with Virtana Service Observability (formerly Zenoss Cloud) and Virtana Service Dynamics 6.9.0
Release 1.5.0
Move to ZPL 2
Release 1.4.4
Fix for ticket 16052-19846
Release 1.4.3
Add
commit()after each device on install to prevent db conficts
Release 1.4.2
Fix to stop continually refreshing browser for BGP and EIGRP protocols
Release 1.4.1
JS fixes, updates for 4.2.4 to fix AttributeError
Release 1.4.0
Internationalize and add basic VRRP support, fix LPD plugin
Release 1.3.0
ISIS added, cleanup
Release 1.2.3
Remove propietary HSRP modeling, js fixes, pyflakes cleanup
Release 1.2.2
Added README.rst symlink
Release 1.2.1
Mibs added, polishing
Release 1.2
Remove dependencies on Calcperf and configurable thresholds
Release 1.1.1
Event class typo fix
Release 1.1.1
Updates to bad values checking
Release 1.1.9
Show event aggregated severity info for components
Release 1.1.8
New event classes, add in calcperf datapoint and configurable threshold
Release 1.1.7
Switch events to go to different locations
Release 1.1.6
Fix device searching, typo fix, add doc file
Release 1.1.5
Fix device lookup, make the interface look prettier
Release 1.1.4
Search on layer 3 catalog first before global catalog
Release 1.1.3
Fix EIGRP modeler, 2.x junk cleaning
Release 1.1.2
Sanitize
neighborMap, graphs updates
Release 1.1.1
Update modeler plugin to ignore administratively down devices.
Release 1.1.0
Allow monitoring to be turned off, typo fix.
Release 1.0.9
Fix objects.xml for 2.4, fix ZPT for OSPF
Release 1.0.8
Bug fixing, search for component IP addresses
Release 1.0.7
Add transition count graph, change to findDevice()
Release 1.0.6
Minor fixes, UI enhancements for 2.4
Release 1.0.5
More updates to BGP modeling&monitoring, modeling fix
Release 1.0.4
BGP monitoring updates
Release 1.0.3
OSPF&EIGRP added, minor cleaning
Release 1.0.2
Initial Release, BGP monitor/modeling